Safety Instruction
1.For security, please read the user manual carefully before initial operation;
2.Please be sure the power is off before connecting, the product is produced without fuse;
3.This system must not endanger life or property during the running failure or its security risks
have been eliminated.
Specification
Working voltage: 12-265V AC/DC
Loading capacity: 1.5W
Weight: 156g
Flashing frequency: 1Hz
Installation method: Vertical/horizontal
Working temperature: -20°C~+60°C
Protection level: IP54
Size: 60*85mm
Mutiple Voltage Flash Lamp
Antenna This is used to extend the effective distance of controller Waterproof and dustproof It is made of plastic material IP 54 .
Notice：
1,Terminal 1 is for connectino thepower input; working voltage is 12-265VAC/DC.
2,Terminal 2 is for connecting the antenna of RF controller to extend the effective working distance
Instruction:
After power the lamp on, LED will start fashing in 1HZ(default setting).
sW1 is the switch for selecting flashing or on mode of the lamp.CAP short connectsthe 2 pins; the lamp is in flashing mode. Remove the CAP from 2 pins, the lamp is inon mode.
Be Careful, the whole board includes the components are with high voltage. Alwaysmake sure power is off before you open the cover
Installation：
Open the package; take out the products and all the accessories. Removing the antenna by rotatinganticlockwise.
Mark 2 holes on the wall by using the fixing hole of bracket.
Drilling two 6mm diameter holes and one 10mm diameter hole. Then put the expansion plug intothe 6mm diameter holes. Put the wires through 10mm diameter hole.
Put the power wire and antenna through the cable holes in the holder. And fix the holder to thewall by provided 4mm*30mm self-taping screws.
Connect the wire and antenna to the correct terminals.
Put the cover back and make sure the cover is fastened with the bottom base without any gap.Then screw the antenna up and turn clockwise to make it tight.
Always install the holder and lamp upright to the ground. Horizontally installation may cause therain go inside the lam and damage the board.
wide range of uses:
Garage doors, Electronic gates, Barrier gates, sliding doors, automatic doors, rolling doors, shutters
Electrical appliances/Home automation i.e. lights, Alarm system, access control system
The package contains:
1X flash lamp
1X antenna
2X Screws
1 X English User Manual
Safety Instruction
1.For security, please read the user manual carefully before initial operation;
2.Please be sure the power is off before connecting, the product is produced without fuse;
3.This system must not endanger life or property during the running failure or its security risks
have been eliminated.
Specification
Working voltage: 12-265V AC/DC
Loading capacity: 1.5W
Weight: 156g
Flashing frequency: 1Hz
Installation method: Vertical/horizontal
Working temperature: -20°C~+60°C
Protection level: IP54
Size: 60*85mm
Mutiple Voltage Flash Lamp
Antenna This is used to extend the effective distance of controller Waterproof and dustproof It is made of plastic material IP 54 .
Notice：
1,Terminal 1 is for connectino thepower input; working voltage is 12-265VAC/DC.
2,Terminal 2 is for connecting the antenna of RF controller to extend the effective working distance
Instruction:
After power the lamp on, LED will start fashing in 1HZ(default setting).
sW1 is the switch for selecting flashing or on mode of the lamp.CAP short connectsthe 2 pins; the lamp is in flashing mode. Remove the CAP from 2 pins, the lamp is inon mode.
Be Careful, the whole board includes the components are with high voltage. Alwaysmake sure power is off before you open the cover
Installation：
Open the package; take out the products and all the accessories. Removing the antenna by rotatinganticlockwise.
Mark 2 holes on the wall by using the fixing hole of bracket.
Drilling two 6mm diameter holes and one 10mm diameter hole. Then put the expansion plug intothe 6mm diameter holes. Put the wires through 10mm diameter hole.
Put the power wire and antenna through the cable holes in the holder. And fix the holder to thewall by provided 4mm*30mm self-taping screws.
Connect the wire and antenna to the correct terminals.
Put the cover back and make sure the cover is fastened with the bottom base without any gap.Then screw the antenna up and turn clockwise to make it tight.
Always install the holder and lamp upright to the ground. Horizontally installation may cause therain go inside the lam and damage the board.
wide range of uses:
Garage doors, Electronic gates, Barrier gates, sliding doors, automatic doors, rolling doors, shutters
Electrical appliances/Home automation i.e. lights, Alarm system, access control system
The package contains:
1X flash lamp
1X antenna
2X Screws
1 X English User Manual
С***ч –
отличный товар!!!! установка быстрая. дистанционно ворота на порядок метров открываются
P***s –
bardzo dobra lampa sygnalizacyjna zasilana 230v i 24v. ma również podpiecie do anteny wzmacniającej sygnał jeśli ktoś ma potrzebę. jeśli chodzi o trwałość czas pokaże
Y***o –
Fast delivery, good quality, working fine. The light is bright. Also connected RG58 cable to the antenna, remote control distance is now much longer. Satisfied, recommend
Acquirente AliExpress –
Wszystko ok przesyłka dotarła na czas solidnie zapakowana bez żadnych uszkodzeń działa bez zarzutu polecam
Acquirente AliExpress –
It works well, even fits on the older base, The old one is broken, and this works the same
Acquirente AliExpress –
Fajna mała lampka z uniwersalnym napięciem od 12V do 250V. Dobrze świeci. Polecam sklep fdsmart Store za szybką i kompletną dostawę
e***r –
Ware korrekt angekommen. Erster Eindruck sehr positiv
V***o –
Лампа хорошая точно такая которыми торгуют у нас только в два раза дешевле
Acquirente AliExpress –
Tutto come da foto. Oggetto al di sopra delle aspettative. Venditore consigliato. Comunque oggetto da provare
Acquirente AliExpress –
Produit conforme, installation toute simple. Le multi tension est un vrai plus. Clignote à 1Hz. Look moderne, avec antenne intégré si besoin.